WARNING: This product can expose you to chemicals that are known to the State of
California to cause cancer. For more information, visit www.P65warnings.ca.gov.
A Certified Pre-owned engine is not unlike a Certified Pre-owned car. There are a base set of standards and criteria the engine must meet to pass a Certified Pre-owned inspection. The engines are tested on a SIM test stand (simulates running) meaning the engines are rotated at normal operating RPM so the following can be checked: 1) Compression- Compression testing indicates if the cylinder bore area seals up which is very important for the performance of the engine. Too low compression or uneven compression between cylinders would indicate there is excessive wear on the rings or valves and these could cause high oil usage, check engine light to illuminate or even early engine failure. 2) Oil pressure and oil flow- Oil pressure is key to proper engine lubrication. High oil flow will give you low oil pressure which may be an indication of severe wear on the bearings. Also, the incorrect oil pressure may set a code and illuminate a check engine light if it isn’t correct. 3) Torque to Turn- Torque to Turn measures the amount of resistance for the engine to operate. If the engine is too tight and hard to turn, this may indicate the engine had been improperly maintained. 4) VVT/VCT-Variable Valve Timing and Variable Cam Timing are common on today’s engines and are critical for the engine components to work on-time to optimize performance. When operating properly, these units help control fuel mileage as they reduce compression on the cylinders as the engine gets up to operating capacity. The engines being produced today by vehicle manufacturers are very sophisticated. They are lower cubic inch engines that run at higher RPM’s to create better performance and improved fuel economy. GPT’s engines are 3-7 years old with varying mileages. Mileage is not the best factor to determine the engine’s quality or longevity. Other factors, such as how the engine was maintained by the previous owner are far more significant. The process GPT uses will tell us everything you need to know about the quality of the engine. Your expectations of a GPT engine should be no less than the day it was built. We believe a Certified Pre-owned engine from GPT will provide you a high-quality, high-value replacement engine without being modified or re-machined as remanufactured engines are. 3 Year 100k Mile Warranty
A Certified Pre-owned engine is not unlike a Certified Pre-owned car. There are a base set ofstandards and criteria the engine must meet to pass a Certified Pre-owned inspection. Theengines are...
Available:
Unit may have to be built please call or message for ETA
Inventory By Location:
GPH:0 MCI:0 (+$300 shipping)
Build Time:
Please Contact Sales
Fitment Summary:
$3,269.25
General Information • All engines come with all pictured components. • If no pictures are available, engine will come as a long block with no tin ware, all gaskets, and new oil pump. • Engine...
Inventory By Location:
GPH:2 MCI:0 (+$300 shipping)
Build Time:
3-5 Days
Fitment Summary:
2.0L L4 VINName: N
2.0L L4 VINName: -
N/A Ford Manual 5-Speed
MTX75 Ford Manual 5-Speed
N/A Ford Automatic 4-Speed
4F27E Ford Automatic 4-Speed
FWD
$2,899.00
A Certified Pre-owned engine is not unlike a Certified Pre-owned car. There are a base set ofstandards and criteria the engine must meet to pass a Certified Pre-owned inspection. Theengines are...
Inventory By Location:
GPH:1 MCI:0 (+$300 shipping)
Build Time:
3-5 Days
Fitment Summary:
2.5L L4 VINName: A
TR3160 Tremec Manual 6-Speed
6L45 General Motors Automatic 6-Speed
RWD
AWD
$2,899.00
A Certified Pre-owned engine is not unlike a Certified Pre-owned car. There are a base set ofstandards and criteria the engine must meet to pass a Certified Pre-owned inspection. Theengines are...
Available:
Unit may have to be built please call or message for ETA
Inventory By Location:
GPH:0 DSM:0 MCI:0 (+$300 shipping) IAH:0
Build Time:
Please Contact Sales
Fitment Summary:
3.5L V6 VINName: M
3.5L V6 VINName: V
$5,006.80
General Information • All engines come with all pictured components. • If no pictures are available, engine will come as a long block with no tin ware, all gaskets, and new oil pump. • Engine...
Available:
Unit may have to be built please call or message for ETA
Inventory By Location:
GPH:0 DSM:0 MCI:0 (+$300 shipping) IAH:0
Build Time:
Please Contact Sales
Fitment Summary:
5.7L V8 VINName: T
845RE Chrysler Automatic 8-Speed
850RE Chrysler Automatic 8-Speed
TR6060 Tremec Manual 6-Speed
8HP50 ZF Automatic 8-Speed
8HP70 Chrysler Automatic 8-Speed
8HP70 ZF Automatic 8-Speed
8HP75 ZF Automatic 8-Speed
NAG1 Chrysler Automatic 5-Speed
RWD
AWD
4WD
$4,299.00
SERVICE WARNING: If The Original Engine Has Experienced A Catastrophic Failure - Including Piston, Cylinder Bore, Valve, or Valve Seat Failure -The Intake Manifold Must Be Replaced With A New...
Inventory By Location:
GPH:1 MCI:0 (+$300 shipping)
Build Time:
3-5 Days
Fitment Summary:
3.2L V6 VINName: -
3.2L V6 VINName: X
2.4L L4 VINName: B
2.4L L4 VINName: -
3.2L V6 VINName: S
948TE Fiat Automatic 9-Speed
948TE ZF Automatic 9-Speed
948TE FCA Automatic 9-Speed
FWD
AWD
4WD
$2,350.00
2014-2018 Jeep Cherokee 2 SPEED OPT (DK4)General Information• All transfer cases are remanufactured using strict specifications to ensure a quality build, and to give you peace of mind installing in...
Available:
Unit may have to be built please call or message for ETA
Inventory By Location:
GPH:0 MCI:0 (+$300 shipping)
Build Time:
Please Contact Sales
Fitment Summary:
$349.00
Eliminates dry starts after engine rebuilds •Eliminates initial wear on engine components •Larger capacity 2 gallon stainless steel tank •Includes (1) 1/8” x 1/8” NPT male to Male Fitting •Includes...
Available:
Unit may have to be built please call or message for ETA
Inventory By Location:
GPH:0 MCI:0 (+$300 shipping)
Build Time:
Please Contact Sales
Fitment Summary:
3.8L H6 VINName: -
AWD
$3,201.53
High reliability: Design for optimum bearing stability, oil seal performance, and thermal resistance in conjunction with strict quality control ensure high reliability and excellent field life...
Inventory By Location:
GPH:0 MCI:0 (+$300 shipping)
Build Time:
Please Contact Sales
Fitment Summary:
2.7L L5 VINName: 4
RWD
$1,472.50
High reliability: Design for optimum bearing stability, oil seal performance, and thermal resistance in conjunction with strict quality control ensure high reliability and excellent field life...
Available:
Unit may have to be built please call or message for ETA
Inventory By Location:
GPH:0 MCI:0 (+$300 shipping)
Build Time:
Please Contact Sales
Fitment Summary:
3.8L H6 VINName: -
RWD
$3,918.37
High reliability: Design for optimum bearing stability, oil seal performance, and thermal resistance in conjunction with strict quality control ensure high reliability and excellent field life...